Discussions on everything about the J/30 Sailboat!
With your one stop source
The J/30 Marketplace
Join or Renew
Class Membership
Search

January
M T W T F S S
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
Today's Birthdays
cstoddard
Newest Members
Kenpickard, Danproawesome, Don N, George Leese, ShaneKilberg
926 Registered Users
Crew Manager Boat Websites

Boat Website subscriptions with
Crew Scheduling & Notifications

Created by former J/30 Rhapsody owner

J/30 Social Network
Popular Topics(Views)
861,413 Dacron Main
131,819 Ananda's Refit
Forum Statistics
Forums28
Topics3,768
Posts18,394
Members927
Most Online223
Dec 17th, 2019
Previous Thread
Next Thread
Print Thread
packing gland #18002
10/08/18 11:23 AM
10/08/18 11:23 AM
Joined: Jul 2018
Posts: 76
Burton, Michigan
N
nathankt79 Offline OP
Senior Member
nathankt79  Offline OP
Senior Member
N
Joined: Jul 2018
Posts: 76
Burton, Michigan
Can anyone tell me where to look for quality packing gland assemblies?

Thanks,

Nate

West Marine Affiliate Program

The J/30 Class Association has partnered with West Marine and is now a member of the West Marine affiliate program. You can support the J/30 Class when you make your West Marine purchases online. The J/30 Class Association receives a percentage of sales from your purchases when you click through from our website. Click the logo above and you will be directed to the West Marine website with a cookie that identifies you as a J/30 affiliate. You can also use any discounts that you may be authorized.
Re: packing gland [Re: nathankt79] #18013
10/12/18 06:35 PM
10/12/18 06:35 PM
Joined: Oct 2009
Posts: 69
Belmont, MA
G
Georges Offline
Senior Member
Georges  Offline
Senior Member
G
Joined: Oct 2009
Posts: 69
Belmont, MA
https://www.defender.com/product3.jsp?path=-1|311|2349117|2349129&id=685485

My J/30 is a 1984 model with a 1" shaft - so 1/4" is the size for me.
I do not know if that would be the same with earlier modesl 3/4" shaft.
I love the GTU, have been using it for years now: it does not overheat even if you get a bit paranoid on the tightening, it does not bite (too much) into the shaft either.


-- Georges
Foot Loose #467 - CPYC - Winthrop
Re: packing gland [Re: Georges] #18021
10/15/18 09:05 AM
10/15/18 09:05 AM
Joined: Jul 2018
Posts: 76
Burton, Michigan
N
nathankt79 Offline OP
Senior Member
nathankt79  Offline OP
Senior Member
N
Joined: Jul 2018
Posts: 76
Burton, Michigan
Thank you for the link! That packing does look like the ticket. I don't really know how to tell when the packing is shot. I was able to adjust it this weekend where it didn't leak when engine was off or in neutral...but when the shaft is spinning in forward or reverse, I can see a wet ring just forward of the nut. This was repeated a couple of times while tied up in the slip and I dried everything up in between tests to make sure I wasn't just seeing residual water. However, I never did see a repeatable "drip per minute". The adjustment was done by hand and only amounted to maybe a 16th of a turn tighter. I tightened the jam nut while holding the adjusting nut with a good pair of large channel locks. My thought is that the wet ring is telling me water is lubing the packing against the shaft.

Unless anyone thinks differently, I think I got it adjusted about as good as can be. Please chime in if you don't though. I am pretty new to this.

Thanks,

Nate


Moderated by  David Erwin 

Who's Online Now
0 registered members (), 35 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
Photos
Truckin'
Endeavour (246) Sailing in Prince Edward Island
First cruise
Fotos Regatas 2017 Tomine Colombia
Regata Armada Tomine Colombia Julio 2017
Recent Posts
COMPLETE SET OF UPPER/LOWER RUDDER GUDGEONS, PINS $325.00
by Rhapsody #348. 01/16/21 06:55 PM
Dacron Main
by B Davis. 01/16/21 03:24 PM
Introduction and Asking for Advice
by neumannaudio. 01/15/21 04:00 PM
Wanted - Triple Deck Organizer - Found One
by B Davis. 01/05/21 03:36 PM
Stern Perch Seats
by Michael L. 01/05/21 09:19 AM
prebend
by Claribertz. 12/30/20 03:43 AM
Winter boat cover
by Gene A Trentham. 12/18/20 03:37 PM
Engine Housing Access Hatch
by Michael L. 12/18/20 03:32 PM
Aluminium Spinnaker Pole
by Michael L. 12/18/20 02:17 PM
Powered by UBB.threads™ PHP Forum Software 7.6.1.1