J/30 Class Association Forums J/30 Marketplace Sails & Equipment for Sale Hull # 229 Falcon parts for sale

mast
rudder
engine
hatches

will have pictures and complete inventory with prices as soon as snow clears

I am looking for a stern pulpit. If you are selling Falcon's please send a price to Dave@j30.us Thanks!

Blew-J is looking for some stanchion's & bases + hatches and side ports if they're in good condition. Also would be interested in the boom price and if there are self tailing primaries .

I need a rudder for my J30 charter boat. Please, con,act me asap, Ivan. 787-667-7778.

Support arms on the forward hatch, or perhaps the entire hatch.

Hi Steve,

Do you have a rigid boom vang for sale?, and what about the Yanmar 2gm panel of instruments, if you have one. 787-667-7778

Thanks, Ivan

Im always looking for parts...do you have pics? List yet?

Hatches, Spinnaker pole and KVH sailcomp 103AC display

Hi, what parts are still available?

what are you looking for I have a lot left

Hi I could use a front hatch still available?

please advise


thanks

Barry Butler Defender

Will take the stern pulpit if still available.

Also looking for the wood steps.

Hi Dave
Would you still have a bow pulpit for sale?

Thanks

Is anyone receiving a response from Steve Higginbottom Sr.?

hi dave
the stern rail is yours just tell me how you want to proceed

yes I have the bow pulpit $500.

I have the 3 hatches as a package for $200.

I'll take the hatches

Throw in the anchor locker cover as well?

Do you have the fiberglass hatch for the main companion way? The one that is screwed down to the deck?

yes I have it

Steve, you can email to planxty312@yahoo.com to arrange for the hatches.

I need a hinge for my anchor locker. The propane locker lid has identical hinges. I need one.

How can I reach the current Falcon owner - looking for stern pulpit. Please send me a message to dave@j30.us.

Thanks,
Dave

I was able to connect with Steve. Thanks!

Anyone know the best place to get a Barient 21?

Dave - I found some in a consignment shop when I needed to replace one. It was gummed up because the grease turned to tar, but after disassembly and cleaning the winch worked like new.

I have a full suite of original Barient winches all in perfect condition. $500 for the lot.

I'm looking for the aluminum track that holds the chart table to the cabinet?

I am looking for the three wooden steps on the engine cover. If available, send a message to dave@j30.us.

Thanks!
Dave

I'm Interested in a 2QM15 instrument panel and wiring harness extension--- mine's a melted mess. joe@heinzle.org if you still have one.

If it's a Yanmar 2QM15, I'm in need of a cylinder head assembly.

J

Hi -

Do you have an anchor hatch or swim ladder?

Regards

I snapped my boom today...is yours still available?

Jay

Steve replied in an email that the boom is gone.

Jay, years ago my boom snapped at the vang attachment point. I removed the vang ss strap, had the boom butt welded then had aluminum angle iron pieces (about 18" long) welded to the top and bottom of the boom, centered over the butt weld. We repositioned the vang attachment strap. It looked like hell but lasted 2 years until we got a new boom section
The main was loose footed so the angle iron on top didn't cause any issues

Hi. I'm interested in your mast, front starboard port window, white stern light on the push pit, stanchons, green/red running lights on the bow pulpit. My J 30 was pretty beat up by hurricane Irma/Maria.
Thank you very much

We have the following J30 parts available for sale:

Full Mast with complete Standing rigging (No boom): $4500
Yanmar 2QM15-F with Transmission : $1500
Complete set of original Barient Winches (2) 25's, (2) 21's, (2) 10's :$300
Original Tiller Handle : $100


Plus shipping.

Email slesterhii@gmail.com

Thanks,
Steve Jr.

Pics?

Hello Steve,
This is a very old thread, but just checking.
I am the new owner of #378 in need of a mast. Did you find a buyer for the FALCON mast?
Thanks,
John

John Duke 401-277-9880

Looking for almost anything for controls: cleats, blocks, whole backstay setup, vang setup, main sheet rigging. Hull #30 needs a major bit of work to avoid tearing apart another set of lines and to actually be able to pull things in and let them off. I don't need perfect or the highest performance stuff - just tough stuff that won't destroy expensive line or make safely changing settings hard to do and maintain. Vang on? Not any more? Main out? Good luck... Backstay? Get two crew and pull! Getting there.... but can't put in the major $$$ for new everything - already sunk in new main and genoa and new major lines and halyards this winter, so anything used and good would be great. Of course, reliable and really high performance stuff, but used, would be more than welcome! Can't use the new lines until I have good stuff that won't hurt them.

Sorry for the novel...

Bruce ericbrucenash@gmail.com

Oops. 2017... my bad. I guess I hope the thread gods look?

L.L. Boat here- I’d like to get my hands on some toe-rails; specifically the port side and adjacent to the stanchion by the winch. It would sure be nice if you had that in your arsenal.

Sorry i do not have toe rails

Hello OP, Maybe I'm late to the conversation but I'm looking for a Forward Deck hatch (above the v-berth), the smaller one (above the head) and replacement portlights if you have those available. Did you have a bow roller on Falcon? Thanks.

Sorry those parts are gone

I need a new Starboard spreader -- just the extrusion. Not the bracket or tip. I'd take both sides. Any chance those are available? Or leads from anyone on where to source?

sorry those parts are gone. try Rigrite?

Any chance you still have the shaft strut?

sorry no

Do you have the Martec prop?

sorry no

Hi there Steve,

You still have a rudder on your hands?